Manufacturing

Controlled production, from coil to bundle

At our Bozüyük plant, welding, heat treatment, testing and finishing run within one production flow.

Capacity
1,500 t/month
Declared monthly production capacity
Tubes
Ø6 – Ø323.9 mm
Outside-diameter range
Profiles
10×10 – 200×200 mm
Square; rectangular 20×10 – 200×100 mm
Wall
0.5 – 8.0 mm (tubes and profiles)
All product families
Length
1,500 – 24,000 mm
Length tolerance −0 / +5 mm
Finish
180 – 600 grit
Custom finishes on request

Process

ERKINOX production in ten steps

  1. Stainless steel strip on the decoiler
    STEP 01 / 10

    Coil and slitting

    Production starts when stainless steel coils are loaded onto the decoiler. Coils are slit into strips at the order width; grade, wall thickness and width are selected according to the order.

  2. Forming roll stations
    STEP 02 / 10

    Cold forming

    Roll stations form the strip step by step into a round section. Square and rectangular profiles reach their final geometry through calibration rolls.

  3. TIG welding arc and laser welding headTIG welding arc and laser welding head
    STEP 03 / 10

    TIG and laser welding

    Tubes and profiles are made with two welding methods: TIG (tungsten inert gas) and computer-controlled laser welding. The method is chosen by product, wall thickness and application.

  4. Weld bead rolling unit
    STEP 04 / 10

    Weld bead rolling

    Internal and external beads formed on the weld seam are corrected by controlled cold plastic deformation with special rolling wheels and an internal support mandrel.

  5. Bright annealing furnace
    STEP 05 / 10

    Bright annealing

    A fully automatic bright annealing unit carries out heat treatment in-line in a protective atmosphere. Ductility and corrosion resistance are restored; the surface does not oxidise.

  6. Eddy current test screen
    STEP 06 / 10

    Eddy current testing

    Eddy current testing is a non-destructive method that detects discontinuities in the weld seam and tube surface without contact. It allows fast inspection on the production line.

  7. ERKINOX hydrostatic test unit
    STEP 07 / 10

    Hydrostatic testing

    Tube samples taken from the line at set intervals are filled with water and tested under controlled pressure. This verifies the leak tightness of the weld seam and the pressure resistance of the tube.

  8. Pickling bath
    STEP 08 / 10

    Pickling

    After welding and heat treatment, the oxide layer and heat tint on the surface are removed by pickling. The cleaned surface passivates and fully regains the corrosion resistance of stainless steel.

  9. Polishing rolls
    STEP 09 / 10

    Polishing and surface finishing

    Products are prepared with 180, 240, 320, 400, 500 or 600 grit finishes, or custom surface work on request. Cutting to length is done in the range 1,500–24,000 mm with a −0 / +5 mm length tolerance.

  10. Strapping and ERKINOX-labelled bundlesStrapping and ERKINOX-labelled bundles
    STEP 10 / 10

    Packing and labelling

    Bundles are strapped and wrapped in protective stretch film. Each bundle ships with an ERKINOX label carrying batch no., size, grade, surface, length, quantity, metres, weight, standard and production date.

Technologies

Two welding methods, one quality standard

  • TIG (tungsten inert gas) welding
  • Computer-controlled laser welding
  • Fully automatic in-line bright annealing
  • Eddy-current and hydrostatic testing during production
  • Special production in duplex 1.4462 (SAF 2205)
Quality control

Plant

Inside the Bozüyük plant

Full gallery
Tube and profile mill lines
Tube mills and coil storage at the Bozüyük plant
Bundles ready for shipment
Production hall
Bundled square and rectangular profiles

Aerial view

Bozüyük OSB from above

Our production facility and office building in the Bozüyük Organised Industrial Zone, Bilecik.

Roof of the ERKINOX facility
Production plant and office building
Entrance façade

Project · Stock · Custom production

Let’s specify the exact size you need.

Share product type, grade, size, wall thickness, length and quantity — our sales team will respond to your standard or custom-size request.